Preview

Agricultural Engineering (Moscow)

Advanced search

NORMALIZATION OF THE PERMISSIBLE ERROR AND THE CHOICE OF MEASUREMENT TOOLS FOR CONTROLLING DEVIATIONS IN THE SHAPE AND LOCATION OF SURFACES

https://doi.org/10.26897/2687-1149-2021-2-51-57

Abstract

The reliability of repaired engines is determined by many factors, among which the accuracy of the geometric parameters of engine parts plays an important role. Errors in the shape and location of the surfaces of parts cause additional acceleration of moving parts and reduce the accuracy of kinematic pairs. Violation of the movement kinematics of parts leads to a deterioration in the technical performance of the engine. In this regard, increasing the level of metrological control of shape deviation and surface location is one of the ways to improve the quality of engine repairs. Analysis of the measurement tools recommended in the reference literature has shown that they were chosen irrespective of the controlled values and without taking into account the type of measurement. The purpose of this study is to develop recommendations for improving metrological control of deviations in the shape and location of surfaces of parts during engine repairs. The paper provides theoretical grounds for choosing the criteria for selecting measuring instruments to control deviations in the shape and location of the surfaces of parts, taking into account the relevant formula. The result of indirect measurement and the measurement error (deviation of the shape and location of the surfaces of parts) are considered random values functionally related to the measured values (diameters of a part). The limits of permissible measurement errors and measurement tool errors are determined to control the deviation of the shape and location of the surfaces of new engine parts and parts subject to troubleshooting. The authors have carried out a comparative analysis of the obtained values with the error values of measuring instruments recommended in the reference literature. It has been established that most of the recommended measuring instruments have an error greater than the allowed measurement error. To reduce the risk of accepting parts that exceed the deviation norms relating to the shape and location of surfaces, it has been suggested using special criteria when selecting measuring instruments.

About the Authors

OLEG A. Leonovm
Russian State Agrarian University - Moscow Timiryazev Agricultural Academy
Russian Federation


NINA Zh. Shkaruba
Russian State Agrarian University - Moscow Timiryazev Agricultural Academy
Russian Federation


LAVRENTIY A. Grinchenko
Russian State Agrarian University - Moscow Timiryazev Agricultural Academy
Russian Federation


References

1. Иванов В.П., Семенов В. Качество ремонта машин: состояние и обеспечение // Вестник Полоцкого государственного университета. Серия B: Прикладные науки. 2003. № 2. С. 2-6.

2. Голубев И.Г., Фадеев А.Ю., Макуев В.А. Оценка качества технического сервиса тракторов // Техника и оборудование для села. 2010. № 7. С. 40-41.

3. Leonov O.A., Shkaruba N.Zh., Vergazova Yu.G. Determining the Tolerances in Fitting for Joints with Interference // Russian Engineering Research. 2019; 39, 554-547. https://doi.org/10.3103/S1068798X19070116

4. Qingya Li, Libao Yang, Weiguo Zhao et al. Design of Positioning Mechanism Fit Clearances Based on On-Orbit Re-Orientation Accuracy. Applied Sciences, 2019; 9(21): 4712. DOI: 10.3390/app9214712

5. Erokhin M.N, Leonov O.A., Shkaruba N.Zh. et al. Assessing the Relative Interchangeability in Joints with Preload // Russian Engineering Research. 2020. V. 40. P. 469-472. https://doi.org/10.3103/S1068798X2006009X.

6. Ерохин М.Н., Леонов О.А., Шкаруба Н.Ж. и др. Процентная взаимозаменяемость посадок с натягом // Вестник машиностроения. 2020. № 3. С. 41-44. DOI: 10.36652/0042-4633-2020-3-41-44

7. Чигрик Н.Н., Леонова Л.М. Оценка точности составляющих функционального допуска посадки на долговечность работы вкладышей коренных подшипников коленчатого вала автомобильного двигателя // Вестник Сибирской государственной автомобильно-дорожной академии. 2013. № 6 (34). С. 29-39.

8. Ерохин М.Н., Леонов О.А., Катаев Ю.В. и др. Методика расчета натяга для соединений резиновых армированных манжет с валами по критерию начала утечек // Вестник машиностроения. 2019. № 3. С. 41-44.

9. Набатников Ю.Ф. Обеспечение заданного ресурса соединений деталей машин // Сборка в машиностроении и приборостроении. 2011. № 4. С. 3-8.

10. Набатников Ю.Ф. Повышение ресурса соединений деталей машин с зазором // Автомобильная промышленность. 2012. № 4. С. 15-18.

11. Денисов А.С., Асоян А.Р., Захаров В.П. Контроль макрогеометрических отклонений шатуна при ремонте, для повышения ресурса двигателя внутреннего сгорания // Вестник Саратовского государственного технического университета. 2011. Т. 1. № 1 (52). С. 56-61.

12. Чигрик Н.Н. Исследование влияния погрешности отклонения формы сопрягаемых поверхностей деталей цилиндро-поршневой группы автомобильного двигателя ЗМЗ-511.10 при селективной сборке на точность элементных размеров // Омский научный вестник. 2013. № 3 (123). С. 124-135.

13. Леонов О.А., Шкаруба Н.Ж., Вергазова Ю.Г. и др. Методы и средства контроля качества обработки гильз цилиндров на ремонтных машиностроительных предприятиях // Вестник машиностроения. 2020. № 6. С. 40-45.


Review

For citations:


Leonovm O.A., Shkaruba N.Zh., Grinchenko L.A. NORMALIZATION OF THE PERMISSIBLE ERROR AND THE CHOICE OF MEASUREMENT TOOLS FOR CONTROLLING DEVIATIONS IN THE SHAPE AND LOCATION OF SURFACES. Agricultural Engineering (Moscow). 2021;(2):51-57. (In Russ.) https://doi.org/10.26897/2687-1149-2021-2-51-57

Views: 88


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 License.


ISSN 2687-1149 (Print)
ISSN 2687-1130 (Online)