TECHNICAL CONDITION AND WEAR OF THE LEFT-SIDE KNIVES OF PSKU-SERIES SPEED PLOWS, METHODS OF BRAKING AND WEAR MINIMIZING
https://doi.org/10.26897/2687-1149-2021-6-56-61
Abstract
High-speed plowing forces significant changes in the design of the working elements of the plow. Such changes greatly affected the wear pattern and, consequently, called for modified technical processes of restoring and strengthening. The working body design includes a plowshare, the function of which is performed by the left-side knife. The research purpose was to control the technical condition of the above-mentioned parts of the PSKu-series plow; study the geometry, location, and magnitude of wear; and develop restoration and hardening technologies. The residual values of thickness and width were used as the criteria for wear since they influence the recovery method. These values were controlled by standard measuring instruments - calipers and height gauges. The hardness measured by the Rockwell method (HRC) was used as a criterion for the mechanical properties of the construction material. Studies have shown that the wear on the working surfaces has a rather complex geometry, which is associated with the specifics of the force action of the soil. This defect should be eliminated because the probability of extreme wear in thickness increases when the part rotates. The authors proposed that the wear on the left-side knife should be eliminated by patching with a low-carbon electrode and subsequent hardening with surfacing reinforcement. It has been experimentally established that the wear amounts to about 7 mm in thickness and no more than 8 mm in width for a knife with a 45.. .54 HRC blade. The wear is caused by a hard-facing layer with a hardness of 73...74 HRC on the backside. High-quality heat treatment ensures an increased resistance of the part to abrasive wear. For left-side knives, it is expedient to apply electrode surfacing with a low-carbon rod and the subsequent hardening by surfacing reinforcement.
About the Authors
ALEKSANDR M. MikhalchenkovRussian Federation
SERGEY A. Feskov
Russian Federation
ANTON V. Dyachenko
Russian Federation
ALEKSANDR M. Grin
Russian Federation
References
1. Селиванов Н.И., Запрудский В.Н., Макеева Ю.Н. Моделирование скоростных режимов агрегатов и удельных показателей колесных тракторов на основной обработке почвы // Вестник КрасГАУ 2015. № 1 (100). С. 81-89.
2. Шевченко В.А., Бородычев В.В., Новиков А.Е. и др. Исследование эффективности использования энергии чизельными и лемешными орудиями при основной обработке почвы // Сельский механизатор. 2018. № 10. С. 30-31.
3. Власов Е.Н., Епифанова А.Ю. Влияние скорости машинно-тракторного агрегата на некоторые стохастические характеристики его функционирования // Научно-техническая конференция по итогам научно-исследовательских работ 2019 года: Сборник статей / Отв. ред. В.А. Соколова. 2020. С. 264-267.
4. Лискин И.В., Алдошин Н.В., Горбачев И.В. и др. Совершенствование конструкции плужных лемехов с накладным долотом // Вестник Федерального государственного образовательного учреждения высшего профессионального образования «Московский государственный агроинженерный университет имени В.П. Горячкина». 2018. № 1 (83). С. 15-19.
5. Петухов Д.А., Свиридова С.А., Бондаренко Е.В. Результаты исследования плуга чизельно-отвального типа на отвальной обработке почвы // Техника и оборудование для села. 2016. № 12. С. 10-13.
6. Козарез И.В., Михальченкова М.А., Гуцан А.А. и др. Характеристики лемехов импортного производства и приобретенные дефекты // Труды инженерно-технологического факультета Брянского государственного аграрного университета. 2021. № 1. С. 70-84.
7. Козарез И.В., Михальченков А.М., Ковалев А.П. Способ восстановления рабочей поверхности лемеха с лучевидным износом: Патент на изобретение RU2464146 C2, 20.10.2012. Заявка № 2010150004/02 от 06.12.2010.
8. Белоус Н.М., Михальченков А.М., Кожухова Ю.И., Козарез И.В. Способ восстановления плужных лемехов: Патент на изобретение RU2412793 C2, 27.02.2011. Заявка № 2008147653/02 от 02.12.2008.
9. Титов Н.В., Коломейченко А.В., Соловьев Р.Ю. и др. Результаты производственной проверки экспериментальных упрочненных износостойкими материалами ножей скоростных плугов // Инновации в АПК: проблемы и перспективы. 2020. № 3 (27). С. 90-97.
Review
For citations:
Mikhalchenkov A.M., Feskov S.A., Dyachenko A.V., Grin A.M. TECHNICAL CONDITION AND WEAR OF THE LEFT-SIDE KNIVES OF PSKU-SERIES SPEED PLOWS, METHODS OF BRAKING AND WEAR MINIMIZING. Agricultural Engineering (Moscow). 2021;(6):56-61. (In Russ.) https://doi.org/10.26897/2687-1149-2021-6-56-61