On determining the sharpening angle of knife blades used in feed grinders operating under conditions of abrasive wear

Enhancing blade durability and determining optimal sharpening angles are critical for extending the service life and increasing the efficiency of feed choppers and industrial processing machinery. This study aims to determine the optimal sharpening angle for feed chopper blades subjected to through-hardening (volumetric quenching) followed by low-temperature tempering under abrasive wear conditions. Experimental samples were fabricated from U7 steel (GOST 1435-99) with sharpening angles of 10°, 20°, and 30°. Heat treatment produced a uniform fine-needle martensite structure across the entire cross-section. The resulting hardness was 740 HV, a 2.96-fold increase over the initial microhardness of 250 HV. Microstructural analysis revealed decarburizationinduced iron oxides at depths of up to 0.079 mm; consequently, suggesting that controlled-atmosphere furnaces should be used during quenching. Wear resistance was tested over a 100-hour period using a custom-made laboratory installation with quartz sand as the abrasive medium. The initial cutting-edge radius ranged from 20 to 35 μm. Under abrasive wear, the smallest increase in edge radius (blunting) was observed in the 10° blades (120 μm), while the 30° blades showed the greatest increase (185 μm). Conversely, the 30° sharpening angle exhibited the lowest overall width wear, while the 10° angle showed the highest. For cutting root crops without impact loads, the 10° sharpening angle is optimal. Furthermore, increasing the cutting speed from 5 to 7 m/s accelerated the dulling rate by 81.5%. These findings provide a technical basis for the design and maintenance of high-efficiency feed choppers and processing equipment

1. Lyalakin V.P., Aulov V.F., Ishkov A.V., Kravchenko I.N., Rozhkov Y.N. Study of the wear resistance of knives during operation and assessment of effective methods for their strengthening. Problemy mashinostroeniya i nadezhnosti mashin. 2024;1:97-106. (In Russ.) https://doi.org/10.31857/S0235711924010117

2. Shcherbina V.I., Poluyan V.A. Increase of knifes durability of drum-type grinders of feed harvester combines. Don Agrarian Science Bulletin. 2012;1:35-39. (In Russ.)

3. Sayfullin R.N., Arbuzov R.F., Biryukov A.L. Influence of electric spark treatment modes on the wear resistance of hardened knives blades. Machinery Technical Service. 2023;61(3):87-93. (In Russ.)

4. Saifullin R.N., Arbuzov R.F., Biryukov A.L. Effect of electrospark hardening time on wear resistance of hardened knife blades. Strengthening Technologies and Coatings. 2024;20(10):458-463. (In Russ.)

5. Yakovlev S.A., Kurdyumov V.I., Proshkin V.E. et al. Results of metallographic studies of cutting parts of cultivator sweeps made of the 30MnB5 steel. Tractors and Agricultural Machinery. 2024;91(5):637-645. (In Russ.)

6. Yakovlev S.A., Kurdyumov V.I., Ayugin N.P. et al. Results of structure and microhardness of cutting parts of paws of John Deere cultivators. Strengthening Technologies and Coatings. 2023;19(12):538-542. (In Russ.)

7. Yakovlev S.A, Kurdyumov V.I., Gluschenko A.A., Sotnikov M.V., Petryakov S.N. Providing self-sharpening of the cutting parts of working bodies of agricultural machinery by point electromechanical processing. Strengthening Technologies and Coatings. 2021;17(9):419-423. (In Russ.)

8. Ipatov A.G., Shmykov S.N., Pervushin V.F., Malinin A.V. Hardening Schumacher Pro Cut segmented knives by laser hardening. The Bulletin of Izhevsk State Agricultural Academy. 2023;4(76):63-68. (In Russ.)

9. Karpin V.Yu. The influence of the sharpening angle of knife blade on the energy consumption of the chopping operation. Sovremennye nauchnye issledovaniya i innovatsii. 2015;3-1:163-166. (In Russ.) URL: https://web.snauka.ru/issues/2015/03/48941

10. Ayugin N.P. On the issue of identification of the specific cutting force of corn stalks. Vestnik of Ulyanovsk State Agricultural Academy. 2025;2:203-211. (In Russ.)

11. Ayugin N.P., Semashkin N.M., Kurdyumov V.I., Prikazchikov V.S. On the study of the zucchini crushing process. Vestnik of Ulyanovsk State Agricultural Academy. 2024;4:182-191. (In Russ.)

12. Ayugin N.P., Semashkin N.M., Kurdyumov V.I., Romanov D.B. Study of the cutting process of fodder beet. Vestnik of Ulyanovsk State Agricultural Academy. 2024;4:173-181. (In Russ.)

13. Ayugin N.P. Identification of the specific cutting force of corn cobs. Vestnik of Ulyanovsk State Agricultural Academy. 2025;2:212-220. (In Russ.)

14. Ayugin N.P., Semashkin N.I., Romanov D.B. et al. The influence of design and kinematic parameters of the knife on the specific cutting force of the sorghum-sudan hybrid. E3S Web of Conferences. 2025;623;04011. https://doi.org/10.1051/e3sconf/202562304011